INSTRUCTIONS

aUTO fLAG

General

  • When operating outdoors do not activate with winds in excess of 15 MPH. 
  • Do not operate the unit during inclement weather conditions.
  • Refer to programming instructions to operate the remote, motor 
  • Before using, insure the bracket contained with the unit is firmly secured to the wall
  • Do not retract the flag while it is draped over the canister. 

Changing Out The Flag

Steps
1. Unfurl the flag while in the flag mount.
2. Remove the flag mast and unit from the flag mount and lay the entire unit on a flat surface.
3. Using a Phillips head screwdriver remove the two screws holding the the flag guide which, the metal device guiding the flag edge.
4. Remove the Flag from the tube.
5. The banners or flags are easily interchanged by removing the original cartridge and replacing it with a new one of your choosing.
6. Lift the tube up to release the pronged edged carefully slide the tube out with motor and antenna wire out of the canister.
7. Thread the flag guide to the edge of the flag and screw the flag guide back on the plate using the two screw with a Phillips head screw driver.
8. Insert the tube by threading the antenna wire in the hole and the proceed end first; than push the spring pin on the other side and slide up until the pin is in the locked position.
9. Place the entire unit back into the flag mount.
10. Operate the remote to insure the flag is at the desired length.
11. If an adjustment is required refer the programming instructions included with the remote control device.
  • Unfurl the flag while in the flag mount.
  • Remove the flag mast and unit from the flag mount and lay the entire unit on a flat surface.
  • Using a Phillips head screwdriver remove the two screws holding the the flag guide which, the metal device guiding the flag edge.
  • Remove the Flag from the tube.
  • The banners or flags are easily interchanged by removing the original cartridge and replacing it with a new one of your choosing.
  • Lift the tube up to release the pronged edged carefully slide the tube out with motor and antenna wire out of the canister.
  • Thread the flag guide to the edge of the flag and screw the flag guide back on the plate using the two screw with a Phillips head screw driver.
  • Insert the tube by threading the antenna wire in the hole and the proceed end first; than push the spring pin on the other side and slide up until the pin is in the locked position.
  • Place the entire unit back into the flag mount.
  • Operate the remote to insure the flag is at the desired length.
  • If an adjustment is required refer the programming instructions included with the remote control device.

Auto Banner

General

  • When operating outdoors do not use in winds in excess of 15 MPH
  • Do not operate the unit during inclement weather conditions.
  • Refer to the programming instructions to operate the remote and motor
  • Before using, insure the bracket contained with the unit is firmly secured to the wall or ceiling
  • Do not retract the banner or flag while it is draped over the canister.

Changing Out the Banner

Steps
1. Unfurl the banner.
2. Remove the banner from the tube.
3. Push the pin inside the side bracket and slowly slide the tube downward.
4. Lift the tube up to release the pronged end and carefully slide the tube with motor and antenna wire out of the cylinder.
5. The banners or flags are easily interchanged by removing the original cartridge and replacing it with a new one of your choosing.
6. Insert the tube by threading the antenna wire in the hole and pronged end first; than push the spring pin on the others side and slide up until the pin is in the locked position.
7. Operate the remote to insure it is at the desired length and rolls up within the canister.
8. If adjustment of length is required refer to programming remote instructions included with the remote control device.
  • Unfurl the banner
  • Remove the banner from the tube
  • Push the pin inside the side bracket and slowly slide the tube downward
  • Lift the tube up to release the pronged end and carefully slide the tube with motor and antenna wire out of the cylinder.
  • The banners or flags are easily interchanged by removing the original cartridge and replacing it with a new one of your choosing.
  • Insert the tube by threading the antenna wire in the hole and pronged end first; than push the spring pin on the others side and slide up until the pin is in the locked position.
  • Operate the remote to insure it is at the desired length and rolls up within the canister.
  • If adjustment of length is required refer to programming remote instructions included with the remote control device

"No part of the flag should ever be used as a costume or athletic uniform. However, a flag patch may be affixed to the uniform of military personnel, firemen, policemen, and members of patriotic organizations. The flag represents a living country and is itself considered a living thing. Therefore, the lapel flag being a replica, should be worn on the left lapel near the heart."

U.S. Code, Title 4, Chapter 1, Section 8(j)